長時間使用發電機組進行工作，出現問題是難免的，重要的是如何去找到問題出現的原因點以及怎么去進行處理，很多用戶說近來自己設備出現油壓過低的現象，這是怎么回事呢？

　　For a long time to use the generator set to work, problems are inevitable, the important thing is how to find the cause of the problem and how to deal with it, many users said that their equipment recently appeared too low oil pressure phenomenon, what is going on?

　　如果發電機組冷卻液的溫度在運行過程中長期保持在較高的溫度值，會導致油的粘度變低，導致油壓過低，油壓失效傳感器或傳感器信號對地短路也可能導致油壓過低，以及其他導致發電機組油壓過低的因素，如換油時未按規定同時更換機油濾清器，導致后期使用時機油濾清器堵塞，造成油路供油不足，油位過低，所用潤滑油的粘度等級不符合發電機組的運行環境要求。等等，都是導致發電機組油壓過低現象出現的因素。

　　If the generator set the temperature of the cooling fluid medium to remain at a high temperature during operation, oil will lead to lower viscosity, leading to low oil pressure, oil pressure failure sensor or sensor signal of short circuit may also result in low oil pressure, and other factors that lead to generating set low oil pressure, such as oil change oil change filter at the same time, not according to stipulations Later use of the oil filter blockage, resulting in insufficient oil supply, oil level is too low, the viscosity of the lubricating oil does not meet the operating environment requirements of the generator set. And so on, are the factors that lead to the phenomenon of low oil pressure of the generator set.

　　那么要怎么進行處理呢？發電機組在運行過程中如出現油壓低報警，應立即停止運行處理。停機后，首先檢查油尺刻度，確保停機五分鐘后油位在量油尺L和H處，接近H的油位為滿油位。如不足，應及時補充同類型油至規定的滿油位。如果檢查發現發電機組冷卻液溫度過高，應立即停機，并采用相應的方法確保冷卻液溫度保持在規定的溫度值內。

　　So how do you do that? If low oil pressure alarm occurs during the operation of the generator set, it should be stopped immediately. After stopping, check the dipstick scale first to ensure that the oil level is at L and H of the dipstick after stopping for five minutes, and the oil level close to H is the full oil level. If insufficient, the same type of oil should be added to the specified full oil level in time. If the coolant temperature of the generator set is found to be too high, the machine should be shut down immediately and the corresponding method should be adopted to ensure that the coolant temperature is kept within the specified temperature value.

　　檢查發電機組的機油濾清器。如果發現機油濾清器堵塞，應及時更換。此外，換油時應同時更換濾油器，以防堵塞而引起機器故障。啟動發電機組前，應檢查機油濾清器是否堵塞，必要時立即更換。檢查發電機組油的粘度是否符合標準。粘度過低，及時更換符合要求的合格油。

　　Check the oil filter of the generator set. If the oil filter is found to be blocked, it should be replaced in time. In addition, when changing oil, the oil filter should be replaced at the same time to prevent blockage and cause machine failure. Before starting the generator set for the first time, check whether the oil filter is blocked and replace it immediately if necessary. Check whether the viscosity of generator oil meets the standard. Viscosity is too low, timely replacement of qualified oil to meet the requirements.

　　瓦斯發電機組如果出現類似問題，首先也要先找原因再去做處理，如果無法檢查原因，請請維修工程師查找并排除故障，不要再自己去隨意拆卸檢查了，非常容易就會造成設備的損壞，然后如果嚴重的話，可能會對操作人員產生一定的危險，所以要慎重。

　　Gas generator set if there is a similar problem, also want to look for the reason to do first, if you can't check the reason, please ask professional maintenance engineers find and troubleshooting, don't go free disassembly check again, very easy to cause the damage to the equipment, then if severe, may produce certain danger to operating personnel, so be careful.

　　發電機組出現了油壓過低的現象怎么處理？以上便是問題的解答內容了，如果您想更多了解相關事項，不妨點擊網站www.a7716.cn直接聯系我們，人員為您做解答！

　　How to deal with the phenomenon of low oil pressure in the generator set? The above is the answer to the problem, if you want to know more about the relevant matters, might as well click on the website www.a7716.cn directly contact us, professionals do the answer for you!