檢查機房內是否有積水或溫度過高，可能導致連接部件腐蝕、電路腐蝕、裂紋和發電機（電球）。由于腐蝕，所有儀器都沒有進行敏感檢查，并且目視檢查瓦斯發電機組是否漏水、漏油和漏氣。

　　Check whether there is water in the equipment room or the temperature is too high, which may cause corrosion of connection components, circuit corrosion, cracks, and generators (electric spheres). Due to corrosion, all instruments were not sensitized and the gas generator set was visually checked for water leakage, oil leakage and air leakage.

　　檢查瓦斯機冷卻水箱內冷卻水是否充足，檢查冷卻水箱內節溫器是否腐蝕。如果被腐蝕，則須更換或清潔。保持冷卻水暢通，檢查空氣濾清器濾芯是否干凈，無油污，是否可以更換或清洗。保持發動機進氣口通暢，檢查機油油位及質量（因長期粘度不足或未使用的機油變質，須補充或更換，檢查油水分離器是否有水），如果有水，如果有水，油和水分離器須在水中浸泡很長時間才能更換。

　　Check whether the cooling water in the cooling water box of the gas machine is sufficient and whether the thermostat in the cooling water box is corroded. If corroded, it must be replaced or cleaned. Keep the cooling water unblocked, check whether the air filter element is clean, no oil, whether it can be replaced or cleaned. Keep the engine air inlet unobblocked, check the oil level and quality (due to long-term lack of viscosity or unused oil deterioration, must be added or replaced, check whether there is water in the oil-water separator), if there is water, if there is water, oil and water separator must be soaked in water for a long time to replace.

　　檢查瓦斯儲油箱內的瓦斯是否充足，連接管之間是否有漏油或松動的部位，檢查瓦斯濾清器表面是否有雜質或水，必要時更換或清洗以確保有足夠的燃料和機油。道路暢通，防止瓦斯發電機組組因缺油、油路堵塞、漏風而停止正常發電，避免不必要的麻煩和損失。

　　Check whether the gas in the gas storage tank is sufficient, whether there is oil leakage or loose parts between the connecting pipes, check whether there are impurities or water on the surface of the gas filter, and replace or clean the gas filter if necessary to ensure that there is enough fuel and oil. Smooth road, prevent gas generator group due to lack of oil, oil road blockage, air leakage and stop normal power generation, avoid unnecessary trouble and loss.

　　操作瓦斯發電機組設備前，用500V表測量發電機及控制系統各繞組對地絕緣電阻。在室溫下不應小于2兆歐。如果絕緣電阻低于上述值，則須進行干燥。

　　Before operating the equipment, use a 500V meter to measure the insulation resistance of the windings of the generator and control system to the ground. Should not be less than 2 megohm at room temperature. If the insulation resistance is lower than the above value, it must be dried.

　　啟動發電機組前，須關閉控制柜的開關。啟動時間不超過15秒，間隔不低于2分鐘。次啟動后，高速運轉3-5分鐘，檢查發動機是否漏水漏油，聽瓦斯發電機組組各部件之間是否有異響，檢查控制器上的參數值是否屏幕是否正常，是否有報警或警告提示，如果有警告提示，請按照警告內容進行故障排除。

　　Before starting the generator set, turn off the switch of the control cabinet. The startup time is no more than 15 seconds and the interval is no less than 2 minutes. After starting for the first time, run at high speed for 3-5 minutes, check whether the engine leaks water, listen to whether there is abnormal sound between the components of the gas generator group, check whether the parameter values on the controller screen is normal, whether there is an alarm or warning prompt, if there is a warning prompt, please troubleshoot according to the warning content.

　　瓦斯發電機組長期不用再使用時要注意什么？以上便是講解內容，希望通過我們的分享可以幫助到大家，更多發電機組資訊關注www.a7716.cn后期的更新。

　　What should be paid attention to when gas generator set is no longer used for a long time? The above is to explain the content, I hope that through our sharing can help you, more generator set information to pay attention to www.a7716.cn later update.